NEW Victron 120V Inverter & Charger - 12/24/48V; 500 - 5000 Watts
NEW Victron 120V Inverter & Charger - 12/24/48V; 500 - 5000 Watts
-
Fast, Reliable Shipping — Tracking provided on shipped orders
-
Quick Order Processing — Most orders ship promptly
-
Shop With Confidence — Secure checkout & easy returns
Couldn't load pickup availability
Description
Description
Works in reverse as a charger; supports failover, split phase (using 2 units), and more.
Victron brand inverters in sizes from 500 watts up to 5000. Designed in the Netherlands, these quality inverters output pure sine wave power, feature highest quality case construction, and are reliability and burn-in tested for a lifetime power supply for all your 120 volt devices.
If you don't need an inverter, it is also used in reverse as a high quality high amperage charger - for example charging boat or camper batteries from shore power.
Begin by selecting the input DC voltage you are working with, then select the corresponding size inverter (sizing in watts).
Multifunctional, with intelligent power management
The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger with adaptive charge technology, and a high- speed AC transfer switch in a single compact enclosure. In addition to these primary functions, the MultiPlus has several advanced features, as outlined below.
Parallel operation and three-phase capability
Up to six MultiPlus units can operate in parallel to achieve higher power output.
In addition to parallel connection, three units can be configured for three-phase output.
PowerControl - Dealing with limited generator, shore side or grid power
A maximum generator or shore current can be set with the Multi Control Panel. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist - Boosting the capacity of shore or generator power
This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is often required only for a limited period, the MultiPlus will ensure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
Four-stage adaptive charger and dual bank battery charging for Lithium, Sealed, AGM, Gel and Flooded Batteries
The main output provides a powerful charge to the battery system through advanced ‘adaptive charge’ software. The software fine- tunes the three-stage automatic process to suit the battery's condition and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Charger datasheet and on our website under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.
High start-up power
Essential to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
Search Mode
When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode, the MultiPlus, when operating in inverter mode, is switched off in case of no load or very low load and switches on every two seconds for a short period. If the output current exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
Programmable relay
By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre- alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low).
Remote on / off / charger on
Three pole terminal.
On-site system configuring, monitoring and control
After installation, the MultiPlus is ready to go.
Some basic settings can be changed via DIP switches: remote switch, battery charge voltage and search mode. Use the VictronConnect app or VE-Configure together with the Interface MK3-USB for in-depth configuration.
Remote configuring and monitoring
Install a Cerbo GX, Ekrano GX or other GX product to connect to the internet.
Operational data can be stored and displayed on our, free of charge, VRM (Victron Remote Management) portal website. When connected to the internet, systems can be accessed remotely, and settings can be changed.
Complete model list:
| MultiPlus 12V / 500W / 20A | [data sheet] |
| MultiPlus 12V / 500W / 20A | |
